Plumber's Essentials: Your Key to Bathtub Installation
Plumber's Essentials: Your Key to Bathtub Installation
Blog Article
We have noticed this post involving How to Install a Bathtub listed below on the internet and accepted it made perfect sense to write about it with you on this page.
Mounting a tub isn't precisely rocket science, yet it does call for solid plumbing, carpentry, and sometimes, tiling abilities. Replacing an old bathtub with a brand-new one is likewise a reasonably tough job. If the old tub is conveniently available, the task can move immediately; if you need to open a wall to get rid of the old tub and also place the new bathtub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub and also embeded in the brand-new one. See to it you have certified on your own for the job and also fit attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is better to consider utilizing one before you begin. Chances are you may require an expert plumber to make tube links.
This post will certainly assist you set up a new bathtub in your shower room if you have actually already bought a brand-new bathtub as well as don't require to alter the setup of your previous water system pipes.
Your devices and also material checklist must comprise the following:
Getting ready for the Setup
First of all, the sustaining structure provided with the bath ought to be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is very important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable tap connectors to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you use all of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last placement.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you must do is detach the water supply. After doing so, switch on the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly bothersome as a result of the restricted accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipelines to the faucets. Have a towel ready for the remaining water that will come from the pipelines. When the supply pipes have actually been gotten rid of, use the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single taps from turning throughout this procedure. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleansed of any type of old securing compound.
Before proceeding to fit the brand-new faucets, compare the pipe links on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Making use of the two wood boards under its feet, position the tub in the required placement. The wooden boards are practical in equally spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four tiny points.
The next objective is to make certain that the bath tub is leveled all round. This can be achieved by checking the spirit level and readjusting the feet on the bathtub up until the spirit level checks out level.
To install faucets, fit the bottom of the outermost versatile faucet adapter to the appropriate supply pipeline by making a compression join; then do the exact same for the various other faucet.
Activate the supply of water and also examine all joints and new pipework for leakages and also tighten them if necessary. Load the bath tub and additionally examine the overflow outlet as well as the typical outlet for leaks.
Ultimately, repair the bath paneling as defined in the supplier's user's manual. Tiling as well as securing around the tub should wait up until the tub has actually been used at the very least when as this will resolve it into its last position.
Fitting New Touches
If the tails of the new faucets are plastic, then you will require a plastic adapter to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet and also the other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, then you will require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the mounting hole in the bath/basin making certain that the washers are in place between the tap as well as the sink. Protect the tap in place with the manufacturer supplied backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with normal faucet ports. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Tub
In the location where the bath meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to crack a stiff seal, triggering the water to penetrate the wall surface between the bath and also the tiling, causing complications with moisture and also feasible leakages to the ceiling below.
You can choose from a selection of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with twists of soaked paper or soft rope. Remember to constantly fill up the bath tub with water before securing, to allow for the motion experienced when the tub is in use. The sealer can fracture relatively early if you do not take into account this activity prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly offered on the marketplace. It is recommended to fit the floor tiles using water-resistant or water-proof adhesive as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
I hope you enjoyed our piece on Tools You Need to Install a New Bathtub . Thanks a ton for finding the time to read through our piece. Sharing is nice. You never know, you might be helping someone out. Thanks a bunch for your time. Please check up our website back soon.
Get An Estimate Report this page